MORE PRODUCTS FROM THE STUKA STUNT WORKS
Last updated October 10, 2010

CONTROL LINE KITS

I am selling out all remaining Brodak products and will no longer be restocking. 

ORDER ANY BRODAK KIT REMAINING IN STOCK
(Not ARF)
AT 20% OFF LIST PRICE

BRODAK ARF'S

Brodak Baby Clown ARF  $ 35.99 plus shipping.

ENGINE ACCESSORIES

CUSTOM MADE ENGINE VENTURIS.

We now have a number of venturis in stock that are custom made and fit for their respective engines. We can also make and fit venturis for engines other than those listed below, but may need the engine in hand in order to fit them. Please check on availability before ordering.

STANDARD VENTURIS
(The type with the needle passing through the center.  Also called a "restrictor" by some.)

Used on most O.S. engines, the Tower .40, the new Magnums, and others.
We can make a standard venturi for any engine on request, but may need the case to ensure proper fit.

Standard custom venturis venturis for engines such as the OS 20-40 FP, the 25-46 LA, the 30 and 35S the Tower .40, and the Thunder Tiger .42 are turned from 1/2 inch stock.
Engines needing larger venturis such as the OS 40 H, OS 40 VF, and the new Magnums are turned from 3/4inch stock.

Standard aluminum venturis, turned from 1/2 inch stock, are priced at $9.50 each.
Standard Delrin venturis, turned from 1/2 inch stock, are priced at $8.00 each.
Standard Delrin venturis, turned from 3/4 inch stock, are priced at $10.00 each.

"TRUE" VENTURIS
(The type where the needle is mounted off to the side and does not go through the venturi.  Also called a "sprinkler" by some.)

Used on most older ASPs, older Magnums, Thunder Tigers, Super Tigres, the Tower .46, and others.
We can make a custom venturi for any engine on request, but may need the case to ensure proper fit.

Most "true venturis" are cut from 3/4 inch Delrin and priced at $12.00 each.

TRUE VENTURIS NOW AVAILABLE FOR ALL PA SERIES ENGINES.

Custom stunt venturis for the PA 40, 51, 61, 65, and 75 available now for $15.00 each.
 

CUSTOM LIGHT WEIGHT TONGUE TYPE MUFFLERS

STRAP-ON TYPE TONGUE MUFFLERS

We have custom made strap-on tongue mufflers for those engines that were not originally equipped for mufflers.  These mufflers are made to fit snugly over the exhaust stack and are held on by a user supplied strap.  I generally suggest using an appropriate sized radiator hose clamp easily obtained at any auto supply store or Wal-Mart.

Strap on tongue mufflers are priced at $19.95 each.

Add $1.00 for a Du-Bro pressure fitting when purchased with muffler.

Strap on tongue mufflers are normally available for the OS 30/35S, 40H, McCoy 35 Redhead, K&B 35 Greenhead, and the old Fox 35.  Others can be made on request.

BOLT-ON CNC MADE CUSTOM TONGUE TYPE MUFFLERS

We offer oversize CNC machined tongue mufflers made to our specifications that offer a larger chamber to reduce back pressure.  These are larger and sturdier than the RSM type of muffler and yet typically weigh only 5/10 to 6/10 of an ounce.  These mufflers are available for most engines equipped for a bolt-on muffler (see chart below) and may be available for other engines not listed here.  If your engine is not listed, please check before ordering.

Our custom tongue type mufflers include mounting bolts and a DuBro pressure tap.  $19.95 each.

BOLT-ON ADAMISIN TONGUE TYPE MUFFLERS

We also offer bolt-on Adamisin type tongue mufflers for most engines including some not listed below. 
If you do not see your engine listed, check.  If we don't have one, we can get one.

Most Adamisin tongue mufflers include mounting bolts but no pressure tap.  $19.95 each.

A Du-Bro pressure tap will be included for $1.00 additional.

SUPER LIGHT WEIGHT TONGUE MUFFLERS--SPECIAL--$14.95 each

So far, these are available only for Super Tigre 35-60 and side exhaust PA engines.  These are CNC made in China and weigh about 3/10 ounce.

A Du-Bro pressure tap will be included for $1.00 additional.
 

CUSTOM LIGHT WEIGHT TUBE TYPE MUFFLERS

ADAMISIN TUBE TUBE TYPE MUFFLERS

We offer custom tube type mufflers made by Art Adamisin that are light, quiet, and non-restrictive. 
These mufflers are made to our size and specifications, have a bead blasted finish, and include the mounting bolts and may be tapped for muffler pressure. 
These tube mufflers are generally a bit quieter and produce a deeper tone than a tongue muffler, and weigh approximately 1.6 ounces.

Most Adamisin tube mufflers include mounting bolts but no pressure tap, and are priced at $ 29.95 each.

A Du-Bro pressure tap will be included for $1.00 additional.

CNC MADE TUBE TYPE MUFFLERS

We now offer a CNC machined (no weld) tube muffler that is even lighter than the mufflers above. 
These have a polished finish and an approximate weight of 1.2 ounces.

Our CNC machined tube mufflers are priced at $ 39.95 each.

A Du-Bro pressure tap will be included for $1.00 additional.

We normally have bolt on tube and tongue mufflers in the following sizes to fit the following engines:

1 -- 1.378          Fox 35 (50th anniversary), Irvine 36, TT 25 Pro, TT 36, OS 25 BB, Leo 37, Fox 50
2 -- 1.400        
  Fox 35 (old), FP 35/40, LA 40/46, Tower 40, TT/Magnum 40 GP, TT 42, ASP 46/53 (late)
3 -- 1.455         
TT 40/46 Pro, Leo 40/46/51, GMS 47, Magnum 40/46/53XLA, ASP 46/53 (old), ASP 52 (new)
4 -- 1.518        
 PA 40/51/61/65 SE, ST 46/51/60, Stalker 46/60

In addition we carry bolt on tongue mufflers for the following:
 

0 -- 1.250         
OS 35S (when engine is drilled) 20/25 FP, 25 LA, TT .25 GP, K&B .40, Stalker STM 40 & 46
02 -- 1.100       
Brodak 40, Irvine 40 Diesel
03 -- 1.044      
 Fox 40 Light Case

Other sizes available on custom order.

6-32 thread DuBro pressure fitting is normally priced at $1.50 each when purchased separately.

NEEDLE VALVE ASSEMBLIES

O. S. NEEDLE VALVE ASSEMBLIES

Standard front mount, now available in two types and priced at $ 13.50 each

.155 OD as made for the Classic OS 35S.  These are also the same size and length as the small ST needle assemblies
.135 OD as made for the 20-40 size FP engines.  These fit the new LA engines exactly.

OS Remote needle assemblies specially priced at $14.95 each complete.

These are new pull-offs of what were supplied on later FP engines.  The package includes a separate venturi spray bar for the front of .135 diameter and a metal rear mounting bracket with the remote needle assembly.

Note:  These are especially suited for profile installations where they can keep your fingers out of the needle and can also be used to "fix" your early version LA engine when the needle breaks off the plastic back plate.

Small Length "Super Tigre" type needle valve assemblies.

These are custom copies of the ST .51 needle assembly.  These are .155 O. D. and measure approximately .250 inch from the shoulder to the spray hole and are a good match for many of the smaller engines such as the OS 30/35S or Fox 35 if you file the sides flat. $9.95 each.

Medium Length "Super Tigre .46" type needle valve assemblies.

No longer available from Super Tigre, these are near perfect copies of the ST .46 needle assembly.  These are the same .155 O. D., and measure approximately .325 inch from the shoulder to the spray hole.  $11.95 each.

Large Length "Super Tigre .46" type needle valve assemblies.

Again, these have the same .155 O. D. but measure approximately .400 inch from the shoulder to the spray hole. $12.95 each.

"Super Tigre" needles only.

Replacement needles for all Super Tigre needle assemblies. 
Slightly longer than the "standard" needle currently supplied by Super Tigre. $3.00 each.

PA SERIES NEEDLE VALVE ASSEMBLIES.

These are the same diameter and length as the ST 46 needle valves, but made with US threads and a nylon "keeper" that holds the needle better. 
These are the ones used by Randy Smith on his PA series of engines. $16.95 each.

PA NEEDLES ONLY. 

Stainless steel replacement needles for the PA assemblies.   $3.95 each.

PA NEEDLES FOR FOX 35.

A replacement assembly for the Fox 35 that have the proper length and turned down to .125 diameter in the choke area to provide the same power as a stock needle but with a much finer thread for precise setting.   $16.95 each.

HEAD SHIMS

These are custom made and available in one size only of .010 inches.  Suitable for the Tower 40, OS .35 and .40, the OS 35S, the Fox .35, the Thunder Tiger .36, and others of similar head size.  $.65 each.  Packet of 3 for $1.95

GLOW PLUGS 
If you are buying an engine, you need a plug.

Fox RC Long Plugs.
These are a good, hot, yet inexpensive plug, suitable for a variety of stunt engines.  Limited availability.   Priced at $4.49 each.

Fox Miracle Plug.
Another good stunt plug.  Designed for 4-cycle running, so work good in 4-2-4 stunt engines.  Limited availability.  Priced at $ 4.95 each.

Thunderbolt RC Long Plugs.
These have become a staple for many stunt flyers.  Priced at $4.99 each.

Thunderbolt 4-cycle Plugs.
Another good performing stunt plug preferred by many.  These have been discontinued, but we have a few remaining in stock.  Priced at $4.99 each.

ALUMINUM LANDING GEAR

MEDIUM FUSELAGE MOUNT.

With a height of 4 inches (from axle height to fuselage mount) and a width (between the wheels of 11 inches -- $8.00 each.
(This is the one the "other guy" calls his large and sells for $10.00.)

LARGE FUSELAGE MOUNT.
With a height of 4 3/4 inches and a width (between the wheels) of 12 1/2 inches -- $9.00 each.

The medium gear is designed for a normal .35 or .40 size plane with a fuselage width of approximately 2 1/4 to 2 3/8 inches, and is suitable for an engine turning a prop size up to about 12 inches in diameter.
Thisis the original gear used on Matthew Neumann's Stuka 97

The large gear is designed for the 46-60 size plane with a fuselage width of approximately 2 3/8 to 2 1/2 inches.
This gear weighs only 5 grams more than our medium gear, and is a good alternate choice for smaller planes when greater prop clearance is desired or for flying out of tall grass.

NOTE: Either gear may be rebent slightly for either greater prop clearance or a wider wheel stance, as appropriate for the airplane on which it is to be used.

METAL WEDGE FUEL TANKS

TANK KITS AVAILABLE IN 4 - 6.5 OUNCE SIZES.  (Supply limited.  Check on availability.)

These are the "standard" size 1 inch high 2 inches wide, wedge tanks made by Brodak, but are not assembled or soldered. These are designed for the person who needs a "special" installation for his stunt plane. The body is bent and the seam is crimped. The ends are formed and everything is ready to solder. You punch the holes, then bend and solder the tubes to fit your configuration. Three pieces of copper tubing are included.
Cheaper and less time consuming than unsoldering and resoldering an already finished tank, and no holes to plug.

The length in inches equals the ounce capacity of the tank. Special prices as follows:

4 & 4 1/2 ounce tank kits - $8.50 each.
5 & 5 1/2 ounce tank kits - $9.50 each.
 

ASSEMBLED TANKS AVAILABLE IN 3 - 7 OUNCE SIZES.  (Some sizes may no longer be available)

Ready assembled tanks are available with either standard venting or with uniflow venting.
NOTE:  Some sizes currently not available.  Check on availability before ordering.

The Standard Square Wedge style tank is designed for mounting inside a full fuselage model. These are one inch high, two inches wide, and the length in inches equals the ounce capacity. With standard venting, one vent tube faces up, and the other down.  With uniflow venting on assembled tanks of the square wedge style, all tubes emerge from the front end cap and face forward, allowing the tank to be easily removable and adjustable by sliding it in and out of its tank compartment.

----------------------------------------------------------------------------------------------------------
Square Wedge Style
-------------------------standard vent--------uniflow vent
3 & 3.5 ounce tanks - (3 and 3.5 inches long) - - - -$9.00 ea. - - - - - $11.00 ea.
4 & 4.5 ounce tanks - (4 and 4.5 inches long) - - - -$10.00 ea. - - - - $11.00 ea.
5 & 5.5 ounce tanks - (5 and 5.5 inches long) - - - -$11.00 ea. - - - - $12.00 ea.
6 & 6.5 ounce tanks - (6 and 6.5 inches long) - - - -$12.00 ea. - - - - $13.00 ea.
7 ounce tanks - - - - - (7 inches long) - - - - - - - - - $13.00 ea. - - - - $14.00 ea.
----------------------------------------------------------------------------------------------------------

HARDWARE

DU-BRO HINGES

Cat. No. 117, these are thin, yet strong "barrel" type hinges that work well for even .65 size ships, and the ones we use on our own models.  Packed 15 to a package.  $3.95 pkg.

3 INCH NYLON BELCRANKS.

Top Flite (Like the current Brodak). Suitable for "Old Time" and "Classic" size planes. Bulk packaged for $1.50 each.

FLEXIBLE LEADOUT WIRE.

The strength of these flexible leadouts is not a question. But flexible leadouts, like flying lines, must be properly terminated, both outside the wing and ESPECIALLY at the belcrank end where it is impossible to observe their condition before each flight. The key to using flexible leadouts is that they must be bushed at the belcrank end with a "C-shaped" tube, through which the cable is snaked and which wraps all the way around the belcrank until its ends touch. The purpose of the bushing is not only to keep the leadout from sawing through the belcrank, but, also, to keep it from flexing under tension. Just remember, anything that flexes constantly will, eventually, break. If terminated properly, however, flexible leadouts are as safe as solids, and are, perhaps, a little easier to care for. If you need longer lengths than 3 foot sections for each leadout, you will need to purchase two packages.

6 foot length of .027. Adequate strength for most planes up to .60 size IF properly terminated. $0.99.
8 foot length of .034. 
Special length and added strength for larger, higher powered planes. $1.49.
8 foot length of .039. 
Special length and added strength for larger, higher powered planes. $1.49.

If there is something you need that is not listed here, ask.
To order, send an e-mail to the address below.

All products priced plus shipping at actual cost.
All prices subject to change.


STUKA STUNT WORKS

Leonard Neumann
8710 Winding Ridge Road
Indianapolis, IN  46217

E-MAIL
MrStuka@CLStunt.com
or
LeonardNeumann@att.net

HOME